Address

Description

0x00

Checksum: The checksum of the TR Configuration block. See Read TR Configuration for details.

0x01 ^[**]

Embedded peripherals: An array of 32 bits. Each bit enables/disables one of the embedded 32 predefined peripherals. Peripheral #0 (Coordinator) is represented by bit 0.0, peripheral #31 (currently not used, but reserved) is controlled by bit 3.7. It does not make sense to enable the peripheral that is not implemented in the currently used device (see Peripheral enumeration).

0x02 ^[**]

0x03 ^[**]

0x04 ^[**]

0x05 ^[*]

DPA configuration bits #0:

  bit 0

Custom DPA Handler: If set, then a Custom DPA handler is called in case of an event. The handler can define user peripherals, handle messages to embedded peripherals, and add special user‑defined device behavior. If set and the Custom DPA handler is not detected the device indicates an error state. Find more information at the Custom DPA Handler chapter.

  bit 1

DPA Peer-to-peer: If set, then DP2P is enabled at [N].

  bit 2

Reserved.

  bit 3

Routing off: If set, then the [N] does not route packets in the background.

  bit 4

IO Setup: If set, then DPA IO Setup is run at an early stage of the module boot time.

  bit 5

User Peer-to-peer: If set, the device receives also peer-to-peer (non-networking) packets and raises the PeerToPeer event.

  bit 6

Stay awake when not bonded: If set, then unbonded [N] never enters low power sleep if the button is not pressed.

  bit 7

Network type: If the bit is set, then the [C] controls the STD+LP network; otherwise, it controls the STD network. The bit can only be changed if the network is empty (no [Ns] are bonded) otherwise the network will stop working.

0x08

TX power: RF output power. Valid numbers are 0-7. Setting this item does not have an immediate effect except these moments:

1.     at Startup,

2.     after discovery (both at [C] and [N]),

3.     at DpaApiSetRfDefaults API and

4.     after DP2P communication.

Use the setRFpower IQRF OS function to set the power at runtime.

0x09

RX filter: RF signal filter. Valid numbers 0-64. Setting this item does not have an immediate effect except these moments:

1.     at Startup,

2.     at DpaApiSetRfDefaults API and

3.     after DP2P communication.

Also, see API variable RxFilter.

0x0A ^[*]

LP RX timeout: Timeout for receiving RF packets at LP-RX mode at LP [N]. The unit is one cycle (one cycle is 46 ms at LP-RX mode). Greater values save energy but might decrease responsiveness to the master interface DPA Requests and also decrease Idle event calling frequency. The valid numbers are 1-255. See also API variable LPtoutRF.

0x0B ^[*]

UART baud rate: Baud rate of the UART interface or the UART peripheral. Uses the same baud rate coding as UART Open (i.e. 0x06 = 57 600 Baud)

0x0C

Alternative DSM channel: A nonzero value specifies an alternative DPA service mode channel.

0x0D

DPA configuration bits #1:

  bit 0

Local FRC: If set, then Local FRC reception is enabled at [N].

  bits 1-7

Reserved.

0x11

RF channel A: Main RF channel A of the main network. Valid numbers depend on the used RF band. Setting this item does not have an immediate effect on [C] or [N] devices except Startup. Use the setRFchannel IQRF OS function to change the RF channel at runtime.

When the [N] is bonded using the traditional bonding or the Smart Connect the channel is automatically inherited from the network member that provided the bonding and then written to the configuration.

0x12

RF channel B: Same as above but the second B channel.