The DP2P Request stored at bufferRF has the following structure:
typedef struct
{
uns8 Header[3]; // 0x000000
uns8 SelectedNodes[30];
uns8 SlotLength;
uns8 ResponseTxPower;
uns8 Reserved;
uns16 HWPID;
uns8 PDATA[sizeofBufferRF - (3+30+1+1+1)*sizeof( uns8 ) - (1)*sizeof( uns16 )];
} STRUCTATTR TDP2Prequest;
Header Must consist of 3 zeros.
SelectedNodes Specifies addressed [Ns] that should send DP2P Response back. See identically named field at Send Selective command. Communication with prebonded [Ns] is not possible.
SlotLength Specifies the timeslot length for the DP2P Response Handshake. The unit is 10 ms. If the default value 0 is used then the timeslot length to accommodate common DPA Request is chosen (see table below). Other values specify a custom timeslot length when the DPA Request might take a longer time (e.g. UART Write & Read) or by contrast to shorten the timeslot if the DPA Request takes short time and its response is also short (e.g. LED Pulse).
ResponseTxPower RF output power used to send DP2P Invite and DP2P Response by [Ns]. Valid numbers are 0-7.
HWPID HWPID of the DPA Request.
PDATA PData part of the DPA Request.
Also, the following variables must be correctly assigned before sending the DP2P Request:
_PNUM PNUM of the DPA Request to execute at [Ns].
_PCMD PCMD of the DPA Request to execute at [Ns].
DLEN Must equal 64.
PPAR Length the DPA Request data payload at the PDATA field.
RF mode used to send DP2P Request depends on the network type. Example of sending DP2P Request:
// Set RF Mode
if ( "is STD network" )
setRFmode( _WPE | _RX_STD | _TX_STD | _STDL );
if ( "is STD+LP network" )
setRFmode( _WPE | _RX_STD | _TX_LP );
// DP2P Request variable
TDP2Prequest DP2Prequest @ bufferRF;
// Prepare DPA Request
// We will read 10 bytes of EEPROM from address 1
_PNUM = PNUM_EEPROM;
_PCMD = CMD_EEPROM_READ;
_DpaMessage.MemoryRequest.Address = 1;
_DpaMessage.MemoryRequest.ReadWrite.Read.Length = 10;
// DPA request data length
PPAR = sizeof( _DpaMessage.MemoryRequest.Address ) +
sizeof( _DpaMessage.MemoryRequest.ReadWrite.Read );
// Save the prepared PData of the DPA Request for later copying
copyBufferRF2INFO();
// Clear DP2Prequest (it clears the Header and SelectedNodes fields)
clearBufferRF();
// Move the saved PData of the DPA Request to the correct place at the DP2P Request
memoryOffsetTo = offsetof( TDP2Prequest, PDATA );
copyBufferINFO2RF();
// Select Node #2 to respond
DP2Prequest.SelectedNodes[0].2 = TRUE;
// Select Node #11 to respond
DP2Prequest.SelectedNodes[1].3 = TRUE;
// Use default timeslot length
DP2Prequest.SlotLength= 0;
// Set TX power for the DP2P Response
DP2Prequest.ResponseTxPower = TX_POWER_MAX;
// Any HWPID is OK
DP2Prequest.HWPID = HWPID_DoNotCheck;
// Set the DP2P packet length
DLEN = sizeof( DP2Prequest );
// Use Access Password for encryption
encryptByAccessPassword = TRUE;
// Encrypt the DP2P Request
encryptBufferRF( sizeof( DP2Prequest ) / 16 );
// Set RF Flags
PIN = _DPAF_MASK;
// And finally send DP2P Request
RFTXpacket();