1 // *********************************************************************
    2 //   DPA Autoexec example                                              *
    3 // *********************************************************************
    4 // Copyright (c) IQRF Tech s.r.o.
    5 //
    6 // File:    $RCSfile: DpaAutoexec.c,v $
    7 // Version: $Revision: 1.17 $
    8 // Date:    $Date: 2017/10/19 07:50:19 $
    9 //
   10 // Revision history:
   11 //   2017/03/13  Release for DPA 3.00
   12 //   2015/08/05  Release for DPA 2.20
   13 //   2014/04/30  Release for DPA 2.10
   14 //
   15 // *********************************************************************
   16 
   17 // Online DPA documentation http://www.iqrf.org/DpaTechGuide/
   18 
   19 // Before uploading this example make sure:
   20 // 1. Autoexec is enabled at HWP Configuration
   21 // 2. Used peripherals are enabled at HWP Configuration
   22 // 3. External EEPROM upload is selected at IQRF IDE. Please note external EEPROM cannot be uploaded using RFPGM.
   23 
   24 // Default IQRF include (modify the path according to your setup)
   25 #include "IQRF.h"
   26 
   27 // Do not check for the Custom DPA Handler existence (we only wrote to the external EEPROM)
   28 #define NO_CUSTOM_DPA_HANDLER
   29 
   30 // Uncomment in order to test Example #3 at [C] device (EEEPROM peripheral space starts at different address)
   31 //#define COORDINATOR_CUSTOM_HANDLER
   32 
   33 // Default DPA header (modify the path according to your setup)
   34 #include "DPA.h"
   35 // Default Custom DPA Handler header (modify the path according to your setup)
   36 #include "DPAcustomHandler.h"
   37 
   38 //############################################################################################
   39 
   40 // Choose example number 1-4
   41 #define EXAMPLE 1
   42 
   43 // -------------------------------------------------------------------------------------------
   44 #if EXAMPLE == 1
   45 // Example #1: Switch on both LEDs
   46 #pragma cdata[ __EEESTART + AUTOEXEC_EEEPROM_ADDR ] = \
   47 /* 1. Green LED ON */ \
   48 5, PNUM_LEDG, CMD_LED_SET_ON, 0xff, 0xff, \
   49 /* 2. Red LED ON */ \
   50 5, PNUM_LEDR, CMD_LED_SET_ON, 0xff, 0xff, \
   51 /* 3. Delay 1s (LEDs will be visible at LP mode) */ \
   52 8, PNUM_IO, CMD_IO_SET, 0xff, 0xff, PNUM_IO_DELAY, 0xe8, 0x03, \
   53 /* 4. End of Autoexec  */ \
   54 0
   55 #endif
   56 
   57 // -------------------------------------------------------------------------------------------
   58 #if EXAMPLE == 2
   59 // Example #2: Open UART @ 9600 baud, write "Hello" to UART
   60 #pragma cdata[ __EEESTART + AUTOEXEC_EEEPROM_ADDR ] = \
   61 /* 1. Open UART at 9600 baud  */ \
   62 6, PNUM_UART, CMD_UART_OPEN, 0xff, 0xff, DpaBaud_9600, \
   63 /* 2. Write "Hello" to UART  */ \
   64 11, PNUM_UART, CMD_UART_WRITE_READ, 0xff, 0xff, /* no read */ 0xff, 'H',  'e',  'l',  'l',  'o', \
   65 /* 3. End of Autoexec  */ \
   66 0
   67 #endif
   68 
   69 // -------------------------------------------------------------------------------------------
   70 #if EXAMPLE == 3
   71 // Example #3: Self modifying Autoexec
   72 #pragma cdata[ __EEESTART + AUTOEXEC_EEEPROM_ADDR ] = \
   73 /* 1. Red LED ON, after the 1st boot it will be self-modified to the Green LED ON + end of Autoexec  */ \
   74 5, PNUM_LEDR, CMD_LED_SET_ON, 0xff, 0xff, \
   75 /* 2. Delay 1s (red LED will be visible at LP mode) */ \
   76 8, PNUM_IO, CMD_IO_SET, 0xff, 0xff, PNUM_IO_DELAY, 0xe8, 0x03, \
   77 /* 3. Write to the EEEPROM a modified Autoexec so next time a Green LED will be ON  */ \
   78 7 + 16, PNUM_EEEPROM, CMD_EEEPROM_XWRITE, 0xff, 0xff, AUTOEXEC_EEEPROM_ADDR & 0xFF, AUTOEXEC_EEEPROM_ADDR >> 8, \
   79     /* new 1. Green LED ON   */ \
   80     5, PNUM_LEDG, CMD_LED_SET_ON, 0xff, 0xff, \
   81     /* new 2. Delay 1s (green LED will be visible at LP mode) */ \
   82     8, PNUM_IO, CMD_IO_SET, 0xff, 0xff, PNUM_IO_DELAY, 0xe8, 0x03, \
   83     /* new 3. End of autoexec  */ \
   84     0, \
   85 /* 4. End of Autoexec  */ \
   86 0
   87 #endif
   88 
   89 // -------------------------------------------------------------------------------------------
   90 #if EXAMPLE == 4
   91 // Example #4: set green LED output pin and set LED on for 1s and then off for 1s, works also at LP mode
   92 #pragma cdata[ __EEESTART + AUTOEXEC_EEEPROM_ADDR ] = \
   93 /* 1. Green LED IO is output */ \
   94 8,  PNUM_IO, CMD_IO_DIRECTION, 0xff, 0xff, /* PORTB.7 = LEDG = Output */ PNUM_IO_TRISB, 0x80, 0x00, \
   95 /* 2. Green LED on for 1s, Green LED off for 1s */ \
   96 17, PNUM_IO, CMD_IO_SET, 0xff, 0xff, \
   97   /* PORTB.7 = 1 => LEDG on */ PNUM_IO_PORTB, 0x80, 0x80, \
   98   /* delay 1s */ PNUM_IO_DELAY, 0xe8, 0x03, \
   99   /* PORTB.7 = 0 => LEDG off */ PNUM_IO_PORTB, 0x80, 0x00, \
  100   /* delay 1s */ PNUM_IO_DELAY, 0xe8, 0x03, \
  101 /* 3. End of Autoexec  */ \
  102 0
  103 #endif
  104 
  105 //############################################################################################